A staple remover is a device used for removing staples originally implanted by Staplers or similar contraption. The origin of the staple remover is, by necessity, an offshoot of the development of the stapler, resulting from a need to remove staples that had been inserted in error, for whatever reason.

Physical Appearance

The root principle of the staple remover is that it's a lever. The simplest staple remover is a length of wedge shaped metal with a flattened, upward-curved and tapered end of dimensions sufficiently narrow as to allow insertion beneath the offending staple. By holding the surface into which the staple is inserted with one hand and applying pressure on the 'lever' with the other, it should be possible to bend the staple in such a way as to loosen or remove it. The issue with such a basic device, however, is that damage to the stapled surface is likely to occur.

Early Staple Removers

Staple removers have existed in one for or another for almost a century. Early staple removers used a lever, as described above, inserted within the body of a larger device. The device served the purpose of both holding the stapled material in place and providing a means to apply firm and even pressure on the lever without requiring too great an expenditure of energy on the part of the user.

A staple remover patented in the early 1920s, for example, used a sprung plunger to apply pressure. The device was placed over the staple with the curved, flattened prongs at one end of the main lever inserted beneath the flat back of the staple, or crown. Pressing the plunger triggered a series of connections that raised the pronged end of the lever sharply, extracting the offending staple with a single swift movement. The prongs lifted the staple on either side, bending the back of the staple downwards and pulling the 'arms' upwards out of the stapled material.

Modern Staple Removers

The modern, conventional staple remover, most often seen in offices, is comprised of a pair of pivotally connected arms that move with a scissoring motion so that one nests within the other. The two arms appear almost identical, apart from the fact that one is small enough to inside the other. There are usually plastic covers that cover the top and bottom that allow for more ergonomic - i.e. comfortable and ideal - contact between the users hand and the staple remover.

The metal arms are shaped like rectangle boxes about 2 inches in length, half an inch across and about quarter of an inch deep. The inner face of each, away from where the fingers make contact with the device, has an open face, which is what allows one to sit inside the other. At one end the rectangular arms are hinged, while at the other tapering claws poke towards each other, so that when pressed together the device closes like a fanged jaw.

Finally, there is a small spring inside at the hinged end that allows the staple removed to snap open when free from artificially-applied pressure. This allows the device to exert its own outward pressure, after closure and insertion beneath a staple, to assist in easy removal from stubborn staples and keep the device open so that it is ready to use straightaway next time. The presence of this springs means that the device can be used with one hand more simply, as well. If there was no spring it would be necessary to open the remover, place it over the staple and insert it - an operation that almost certainly would require the use of both hands.

Simple Summary of Form

To make the average office staple remover easier to imagine, for those who have never seen one:

1. Fold your thumb into your palm and then form your remaining fingers into a V-shape with two fingers forming each side of the form.
2. Turn your hand so that your fingers are roughly horizontal.
3. Perform a cutting, "scissor" motion with your fingers, closing the gap between your second and third fingers.
4. Pretend you have fangs sticking out of the inside edge of the tip end of your second and third fingers.

Using a Staple Remover

To effect removal of a staple from a stapled article, the user should press the two arms of the device together, usually by applying a thumb to the upper plastic element and one or more fingers to the other, lower plastic element element. Then simultaneously drive the teeth of the first and second pair of arms between the crown of the staple and the top sheet of the stapled article, and once the teeth are clenched pull the double-jawed staple remover so as to disengage the staple from the stapled article.

The action of the teeth bends and pulls the staple, stretching it so that the prongs pull upwards and apart. The operation can, equally, be actioned upon the prongs themselves instead of the crown of the staple. In this instance, the staple remover teeth connect beneath the prongs and pull them upwards. The movement, essentially, attempts to restore the staple to its original form, straightening the bent prongs of the staple, so that it can be easily extracted from the other side.

The ability to adapt the device for use from either side means that a partial failure to remove the staple by the crown, which may leave a curled prong in place, can be resolved by turning the stapled article around and uncurling the stubborn prong.

Other Uses

The ingenuity and keen sense of the bizarre common to many members of the human race means a staple remover may be used for many activities other than the removal of staples. Common alternative purposes for staple removers include:

Pretend Vampire Fangs - One part cool trick, one part testament to human foolhardiness, this is one of the most easily-achieved and commonly-performed tricks to be done with staple removers. The trick involves inserting the staple remover into one's mouth in such a manner that, when the mouth clamps down, the staple remover will give the illusion of 'fangs'. This illusion is rarely achieved to the point that the willing suspension of disbelief becomes even a consideration. Occasional screams around any office can be attributed to the poorly planned execution of this trick.

Pretend Crab/Lobster Claws - The activity involves grasping the staple remover with the hands in such a way that, when the hand is closed, the staple remover closes, too. A trick rarely performed with a great depth of skill.

Pretend Castanets - Very similar to 'Pretend Crab Claws', however performed with hands held in the air, and with some discernible rhythm to the opening and closing of the staple remover. Most authentically performed with two staple removers.

Pretend Telegraph - Likely invented by the more history-conscious brother of the idiot who invented the uses above. Involves placing the staple remover flat on a table and pressing down rapidly on the other end in a succession meant to simulate Morse code. A popular companion to this game involves typing a random 'message' in Morse code, recording it, and then translating it into discernible letters (or, when possible, words). Fun for the whole family.

Variations and Availability

Staple removers may commonly be found in different colours and shapes, and with occasional improvements in the fitting of the plastic elements to the fingers pressed against it. Other variations may include rubberized grips or combination with other common office implements. The combination of stapler with staple remover is an ideal one-piece device, for example. In this instance the remover is the most simple lever form, a triangular wedge that can be inserted beneath the staple than rolled upwards to extract it. The arms of the staple remover may be extended backwards so that the device resembles a pair of scissors, providing greater leverage for stubborn staples and heavy duty ones commonly used to secure particularly thick documents.

Stationery stores, and stationery cupboards, are the most common source for the acquisition of staple removers. The most common and basic staple removers are reasonable cheap, but are best guarded in the office environment. Like staplers, they have a habit of disappearing very quickly and quite suddenly if left openly on a desk top. The common need to staple together and ply apart documents means that fellow officer workers passing an unattended desk with a staple remover will invariably pick it up, use it and then forget to return it to your desk¹.