Court Numbering System

• 1 - back right, where the player who has just served stands.
• 2 - front right.
• 3 - front middle.
• 4 - front left.
• 5 - back left.
• 6 - back middle.

"B"

• Back-court hitter -
• Block - using the hands and arms to stop the ball from crossing the net. Extremely tall players find little need to jump, unlike anyone shorter than about 1.90m (6'2").
• Blocker - someone who blocks.

"C"

• Calling - Often when players first begin playing they are told to "Call for the ball" an obvious requirement within a team sport. Actually getting them to do this is incredibly difficult. Calling can also refer to the team chants that occur between rallies as they try to psyche each other out. The whole team may chant "7-4-7 Zoooom" or "Taxi" to draw attention to a spike that hits the back wall of the sports hall or "Yooou are stuffed"¹ to indicate the great block that one of their team has just performed. In truth these types of call are against the spirit of the game and many teams just call there own name at the end of a time-out² or celebrate with high fives.
• Combination - this is an pre-determined attacking play where two hitters jump near the same area of net. The aim is to get opposition blocker to jump with one player, so that the 2nd hitter has an open attack. Examples are the cross-over, piston and tandem.
• Cross-over - a combination play where two hitter approach from different sides of the court and cross behind/in front of each other.

"D"

• Dig -
• Dink - see tip.

"F"

• Free Ball - in fact this is not winning a ball in the local raffle, but actually when the opposition attack is so weak that it should results in a perfect pass into the setter. This should provide the attacking team with the maximum chance of winning the point.

"L"

• Libero - a player who wears a different shirt and can substitute onto court an unlimited number times. They many not serve, block or hit the ball above the height of the net. If they overhand volley a ball inside the 3m line, it may not be hit above the height of the net.

"M"

• Middle player -

"O"

• Outside player -

"P"

• Piston - a combination play where two hitters attack the same area of the net, but at different times. The 1st hitter jumps and as they begin to descend, the 2nd hitter then jumps. The overall effect is that of pistons in an engine.

"R"

• Roofing - in olden times, roofing referred to a player being able to hit a ball onto the floor hard enough that it would bounce up and hit the roof. In the modern day it is a term describing a good block, imagine a roof being made over the ball by the blocker's hand so that it cannot escape.

"S"

• Set -
• Setter -
• Short - a ball set a short distance to a player who is already in the air. It therefore travels a short distance in a short time.
• Side-out - receiving service and winning the rally. In old times (pre-1998) it did not score a point.
• Spike -
• Stuff-block - a blocked ball that rebounds quckly to the floor.
• Swing hitter - see outside hitter.

"T"

• Tandem - a combination play where two hitters attack side by side with maybe 1 metre apart.
• Time-out - a brief delay between rallies which can be called by either the coach or captain. Teams can use this time to break opposition momentum and regather their thoughts. Timeouts usually last 30 seconds.
• Tip - an attack that is just pushed over the net by flicking the wrist. Usually results in the ball going over the top of the blockers and land just behind them. Also known as a dink or dump!
• Tooling - when an attacker deliberately hits a ball off the block so that it ends up out of court, thereby winning the point. Cheeky!

"V"

• Volley - using the fingers of both hands to rebound the ball. In truth it is catching and throwing the ball very quickly. Try putting your hands to together in a praying manner, then move the palms away so that only the finger tips remain in contact. Then rotate your hands above your head so that the palms are up. Finally move the fingers about an inch apart. This is the volleying position.

"W"

• Wiping the block - see tooling.